Link-systems OmniLink II Press Automation Control Manuel d'utilisateur Page 11
- Page / 154
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
August 30, 2002 Manual Version 1.0
2.2
It is also convenient to run the 115VAC power along with the high-speed serial bus cable to each
module(s) enclosure in the same flexible liquid tight conduit with ground, as indicated in Figure 2.2.
Figure 2.2 Serial Bus Connections
3. Dual connector plugs are used for each optional module shown in Figure 2.2 for both the high-
speed serial bus and 115VAC power connection to the module. This allows both the serial bus and
power connections to be strung from module to module as shown in Figure 2.3.
Figure 2.3 Dual Connector Plugs for Modules for Serial Bus and Power
USE THE SWITCH ON THE OPTION INSTALLED
AT THE FAR END OF THE CABLE FROM THE
OPERATOR TERMINAL TO TERMINATE THE
SERIAL BUS CABLE.
OPERATOR
TERMINAL
ENCLOSURE
O
P
T
I
O
N
1
O
P
T
I
O
N
5
O
P
T
I
O
N
3
O
P
T
I
O
N
2
O
P
T
I
O
N
4
SERIAL BUS CABLE AND POWER FOR
MODULES RUN IN SAME CONDUIT
G
N
D
L
1
L
2
115 VAC FROM
LAST MODULE
115 VAC CO NNEC T OR PLUG
FOR THIS MODULE
115 VAC TO N EXT
MODULE
16 GA RE D, WH ITE ,
GREEN WIRES
16 GA RE D, WH I TE ,
GREEN WIRES
PLUGS INTO MODULE
CONNECTOR HEADER
FOR THIS MODULE
SERIAL BUS CABLE
FROM LAST MODULE
SERIAL BUS CONNECTOR
PLUG FOR THIS MODULE
SERIAL BUS CABLE
TO NEXT MODULE
SHIELD MUST BE
CONNECTED TO PLUG
PLUGS INTO MODULE
CONNECTOR HEADER
FOR THIS MODULE
Cable Wire Color Connector
Terminal
White CANL
Orange CANH
Blue GND
Bare Shield
- OmniLink II 1
- Section 1 Introduction 6
- Section 1.3 System Overview 8
- OTHER MODULES TO BE 9
- DEVELOPED 9
- Section 2 Installation 10
- OmniLink II LCD 14
- CRANK OR ECCENTRIC 15
- 8 OR 16 CHANNEL 16
- DIE PROTECTION AND 16
- PROCESS MONITOR 16
- MODULE ENCLOSURE 16
- Section 2.3.1 Conduit Runs 17
- CONNECTION FOR CLOCKWISE 19
- 115VAC CONTROL TRANSFORMER 22
- SECONDARY WINDING 22
- INSIDE OF 25
- OPERATOR 25
- TERMINAL 25
- ENCLOSURE 25
- PRESS CONTROL 25
- OPTIONAL 802-5 29
- SS RELAY MODULE 29
- Customer’s Enclosure 31
- (Optional) 32
- OmniLink II LCD 34
- Section 3.3 Softkeys 36
- Section 3.5 CHG Key 37
- Section 3.6 Arrow keys 37
- Screen Legend 38
- SoftKeys 39
- Press the 45
- ACCESS CODE 45
- Enter the code 46
- (Pasword)for 46
- AUXILIARY 51
- PREVIOUS 53
- & 360 59
- SPM Input Cal # : 64
- Section 5.2.1 Brake Monitor 86
- Section 5.2.8 Diagnostics 90
- Section 5.3 Counters 92
- Section 5.3.2 Stroke Counter 95
- Section 5.3.3 Scrap Counter 95
- Section 5.5.1 Machine Notes 100
- Section 5.5.2 Job Notes 100
- Section 5.5.5 LOGOUT Softkey 101
- Section 5.6.1 Store Setup 102
- Section 5.6.2 Recall Setup 103
- Section 5.6.3 Erase Setup 104
- Section 6.3 Mounting 108
- PROCESS MONITO 109
- DIE PROTECTION & 109
- MODEL 512x 109
- Section 6.4 Wiring 110
- Section 6.5.1 Static 115
- Section 6.5.2 Cyclic 117
- ACCEPTABLE 118
- UNACCEPTABLE 118
- MATERIAL 119
- One Part-Edge 121
- One Part-Pass 122
- Two Part-Edge 123
- Two Part-Pass 124
- Section 6.5.9 Custom 125
- Section 6.6 Configuration 126
- Section 6.7 Operation 128
- Section 6.7.3 Bypass 134
- Section 6.7.4 Reset 136
- Section 7.1 Features 138
- Section 7.2 Specifications 138
- Section 7.3 Mounting 139
- Section 7.4 Wiring 142
- Section 7.4.4 Output Wiring 142
- Section 7.5.2 Always On Mode 145
- Section 7.5.3 Normal Mode 145
- Section 7.5.4 Timed Off Mode 145
- Section 7.5.5 Toggle Mode 146
- Section 7.6 Configuration 147
- Section 7.7 Operation 149
- Section 7.7.2 Reset 153
Produits connexes et manuels pour Instruments de mesure Link-systems OmniLink II Press Automation Control
(77 pages)
(89 pages)Yamaha 407 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Instrumenty muzyczne Yamaha 407.
Dostarczamy 1 pdf podręczników Yamaha 407 do pobrania za darmo według typów dokumentów: Dokumentacja
Commentaires sur ces manuels