Link-systems OmniLink II Press Automation Control Manuel d'utilisateur télécharger pdf (Page 8)

August 30, 2002 Manual Version 1.0

1.3

Section 1.3 System Overview

Figure 1.1 shows the base package hardware components for the OmniLink II Press Automation

Control.

Figure 1.1 OmniLink II Press Automation Control Base System Package

Figure 1.2 (next page) shows the existing and planned components and features of the system with

optional components.

OMNILINK II PRESS AUTOMATION CONTROL

Crank or

Eccentric

Shaft

RESOLVER CABLE

RESOLVER

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 153 154

OmniLink II 1
Section 1 Introduction 6
Section 1.3 System Overview 8
OTHER MODULES TO BE 9
DEVELOPED 9
Section 2 Installation 10
OmniLink II LCD 14
CRANK OR ECCENTRIC 15
8 OR 16 CHANNEL 16
DIE PROTECTION AND 16
PROCESS MONITOR 16
MODULE ENCLOSURE 16
Section 2.3.1 Conduit Runs 17
CONNECTION FOR CLOCKWISE 19
115VAC CONTROL TRANSFORMER 22
SECONDARY WINDING 22
INSIDE OF 25
OPERATOR 25
TERMINAL 25
ENCLOSURE 25
PRESS CONTROL 25
OPTIONAL 802-5 29
SS RELAY MODULE 29
Customer’s Enclosure 31
(Optional) 32
OmniLink II LCD 34
Section 3.3 Softkeys 36
Section 3.5 CHG Key 37
Section 3.6 Arrow keys 37
Screen Legend 38
SoftKeys 39
Press the 45
ACCESS CODE 45
Enter the code 46
(Pasword)for 46
AUXILIARY 51
PREVIOUS 53
& 360 59
SPM Input Cal # : 64
Section 5.2.1 Brake Monitor 86
Section 5.2.8 Diagnostics 90
Section 5.3 Counters 92
Section 5.3.2 Stroke Counter 95
Section 5.3.3 Scrap Counter 95
Section 5.5.1 Machine Notes 100
Section 5.5.2 Job Notes 100
Section 5.5.5 LOGOUT Softkey 101
Section 5.6.1 Store Setup 102
Section 5.6.2 Recall Setup 103
Section 5.6.3 Erase Setup 104
Section 6.3 Mounting 108
PROCESS MONITO 109
DIE PROTECTION & 109
MODEL 512x 109
Section 6.4 Wiring 110
Section 6.5.1 Static 115
Section 6.5.2 Cyclic 117
ACCEPTABLE 118
UNACCEPTABLE 118
MATERIAL 119
One Part-Edge 121
One Part-Pass 122
Two Part-Edge 123
Two Part-Pass 124
Section 6.5.9 Custom 125
Section 6.6 Configuration 126
Section 6.7 Operation 128
Section 6.7.3 Bypass 134
Section 6.7.4 Reset 136
Section 7.1 Features 138
Section 7.2 Specifications 138
Section 7.3 Mounting 139
Section 7.4 Wiring 142
Section 7.4.4 Output Wiring 142
Section 7.5.2 Always On Mode 145
Section 7.5.3 Normal Mode 145
Section 7.5.4 Timed Off Mode 145
Section 7.5.5 Toggle Mode 146
Section 7.6 Configuration 147
Section 7.7 Operation 149
Section 7.7.2 Reset 153

Commentaires sur ces manuels

Pas de commentaire

Link-systems OmniLink II Press Automation Control Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de mesure Link-systems OmniLink II Press Automation Control