Link-systems OmniLink 5000 Manuel d'utilisateur télécharger pdf (Page 5)

Section 5.4.7 Configure Auxiliary Communications ......................... 5.21

Section 5.6 Output Names/Messages .......................................... 5.22

Section 5.6.1 Input Names (option) ..................................... 5.22

Section 5.6.2 Aux. Equipment Messages ................................. 5.23

Section 6 Press Control I/O ....................................................... 6.1

Section 6.1 Press Control Inputs .............................................. 6.1

Section 6.1.1 Run Buttons ............................................. 6.2

Section 6.1.2 Operator Station Selects .................................... 6.3

Section 6.1.3 Prior Action Setup Buttons .................................. 6.3

Section 6.1.4 Top Stops ............................................... 6.3

Section 6.1.5 Emergency Stops ......................................... 6.3

Section 6.1.6 Master Stops............................................. 6.3

Section 6.1.7 Forward/Reverse Motor Contacts ............................. 6.4

Section 6.1.8 Mode Selector Switch...................................... 6.4

Section 6.1.9 Press Line Interface........................................ 6.4

Section 6.1.10 Valve Monitor........................................... 6.4

Section 6.1.11 Lube System I/O ......................................... 6.7

Section 6.1.12 Hydraulic Overload I/O................................... 6.12

Section 6.1.13 Light Curtain........................................... 6.14

Section 6.2 Press Control Inputs (option)....................................... 6.15

Section 6.2.1 Aux. Lube System I/O..................................... 6.16

Section 6.2.2 Run Mode Interlocks...................................... 6.18

Section 6.2.3 Input Board #3 Select ..................................... 6.18

Section 6.2.4 Definable Top Stops ...................................... 6.18

Section 6.2.5 Definable Cycle Stops ..................................... 6.18

Section 6.2.6 Definable Master Stops .................................... 6.19

Section 6.2.7 Continuous on Demand Run ................................ 6.19

Section 6.3 Press Control Outputs ............................................ 6.19

Section 6.3.1 Delayed Main Motor ...................................... 6.20

Section 6.3.2 Flywheel Brake .......................................... 6.20

Section 6.3.3 Auxiliary Equipment Stop .................................. 6.20

Section 6.3.4 Slide Motion ............................................ 6.21

Section 6.3.5 Mode Outputs........................................... 6.21

Section 6.3.6 Stroking Enabled......................................... 6.21

Section 6.3.7 Stop At Top Output ...................................... 6.22

Section 7 Installation ............................................................ 7.1

Section 7.1 Component Mounting ............................................. 7.1

Section 7.2 Field Wiring..................................................... 7.5

Section 7.2.1 Operator Terminal/Card Rack ................................ 7.5

Section 7.2.2 Clutch/Brake Valve........................................ 7.6

Section 7.2.3 Resolver/Encoder ......................................... 7.6

Section 7.2.4 Inputs .................................................. 7.7

Section 7.2.5 Outputs................................................. 7.8

Section 7.2.6 Flywheel Speed ........................................... 7.9

1 2 3 4 5 6 7 8 9 10 ... 114 115

Commentaires sur ces manuels

Pas de commentaire

Link-systems OmniLink 5000 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de mesure Link-systems OmniLink 5000